那么，高爾夫?qū)б曋谱鲿r(shí)的絲網網版如何制作呢，我們選擇一塊1厘米厚的墊板，把它放在絲網網版與網印平臺架子面板的后面，它們之間的這個距離，這就是網距。一般最好是使絲網網版張力大，網距小.，這樣刮印油墨后能及時彈起。在這些過程里，我們力所做到的就是需要精準的手工工藝。

    高爾夫?qū)б曋谱鲿r(shí)還會用到腐蝕這一過程，然而耐腐蝕的感光油墨在使用前，要調整稀稠度，在冬天，油墨很容易凝固?？梢韵劝阉旁诤嫦淅锖嬉粫?huì)兒。烘箱的溫度設置在88度，讓它自動控制，5分鐘后拿出來，充分?jǐn)嚢?，沒有氣泡，像這樣了才能使用。這些都是在實際的過程中得到的一些經驗之談。

    在高爾夫?qū)б曋谱鲿r(shí)準備一把斜面有彈性、平整、無缺口，表面干凈的橡膠刮板。
    再就是準備進口的油墨，在制作時把適量的感光油墨,放在絲網網版的紗面上,形成一個條狀，就可以用刮板開始刮了，刮的時候，用力要合適，速度也要恰到好處，刮1到2遍后，把絲網網版掀開，如果印在不銹鋼板上的感光油墨厚薄非常均勻，就可以用手托在它的反面，把它拿出來，注意不要將涂有感光油墨的那面弄臟。這需要嚴格的管理制度來限制這些過程。要說明的是， 經常會遇到這樣的情況，刮2遍后，效果還是不好，那就要放棄了。否則油墨太厚也是不行的。這些經驗老練的師傅就才會知道這些。

    我們在制作時要調好水溫，在30度左右的溫水中，加入適量工業用弱堿性的碳酸鈉，比例大約是20：1，攪拌均勻后放入感光油墨沒有涂均勻的不銹鋼板，涂層很快就會脫離不銹鋼表面，再用干凈的布把感光油墨徹底擦掉，然后用清水漂洗，用吹風機吹干，就可以重新再印了。把這些工作一步一步地做好，讓我們的高爾夫?qū)б曋谱鞒删返墓に嚻贰?/p>

Golf guides making process when specific methods of operation

    (A) golf guides produced when the surface protection measures required
    Golf guides produced by the light-sensitive ink corrosion-resistant coating, which is a basic infrastructure.
    Guides produced in our production of golf when the purpose of the first 200 mesh screen selection. In these special mesh screen must be a clean, medium size. However, this is some of the process, then it is firmly fixed in the professional manual screen printing platform on the shelf, the stainless steel mesh screen on the center, so that the side with stainless steel mesh screen in the corresponding box to keep 6 cm distance, too close and too far were inappropriate. These, after a series of planning, then, on the appropriate location, use scotch tape all around, stick time must be carefully pressed by hand, sticky side, so as not to screen in transparent tape and between leave air bubbles, so that their full contact, light-sensitive ink on coated stainless steel plate will not be applied to the outside. The middle part just did not stick transparent tape and stainless steel plate the size of the match, so that the light-sensitive ink coated corrosion-resistant when the position will be accurate. After all stick to the surface and then clean up, to keep the screen clean gauze screen. This is what we make in golf guides to some of the basic method of operation.

    So, when making golf guides how to make it mesh screen, we chose a 1 cm thick plate, put it on the wire screen and screen printing platform shelf behind the panel, the distance between them, This is the network distance. Generally it is desirable to screen a large screen tension, mesh away from the small.. This timely after scraping India ink bounce. In these processes, we need to do is force the precise craftsmanship.

    Golf guides will be used when making the corrosion process, corrosion-resistant light-sensitive ink, however, before use, dilute to adjust the consistency, in the winter, the ink is easy to solidification. Can put it in the oven while baking. Set oven temperature at 88 degrees, it automatically controls out after 5 minutes, stir, no bubbles, like the case to use. These are in the actual process to get some of the voice of experience.

    In golf guides prepare a slope when making flexible, smooth, no notch, clean the surface of the rubber scraper.
    Then there are ready to import the ink, the amount of time in the production of light-sensitive ink, on the yarn surface mesh screen to form a strip, you can use a scraper start scraping, scraping, when forced to the right, the speed should be just right, 1 to 2 times after scraping, the mesh screen opened, if printed on stainless steel plate thickness is very uniform light-sensitive ink, you can use the opposite hand under it, take it out, be careful not to coated with light-sensitive ink that side dirty. This requires strict management system to limit these processes. To note is that often encounter such a situation, scraping two times, the effect or not, it would have to give up. Otherwise, the ink is too thick will not work. Seasoned master on these experiences will know.

    We should be fine in the production of water temperature, 30 degrees in the warm water, add appropriate amount of alkaline sodium carbonate for industrial use, the ratio is about 20:1, even after mixing into the light-sensitive ink is not uniformly coated stainless steel plate, coated will soon be out of stainless steel surface layer, and then clean cloth to thoroughly wipe sensitive ink, then rinse with water, dried with a hair dryer, you can re-printed. Step by step to make these work, let our guides made into fine golf crafts.